Buy a bag of titanium dioxide and the label may say rutile or anatase. Same compound, same CAS number 13463-67-7, same white powder in the sack. Yet the two crystal forms behave differently enough that picking the wrong one can turn an exterior coating chalky within a couple of seasons. The choice matters. Here is how the two grades differ, and how to match them to the job. Both are standard items in a titanium dioxide pigment range alongside carbon black and iron oxides.

One Formula, Two Crystal Lattices

Rutile and anatase are both titanium dioxide, TiO2. What separates them is how the titanium and oxygen atoms pack: each builds a different tetragonal lattice, and that geometry drives every practical difference downstream. Anatase is the metastable form; heat it hard and it converts to rutile, typically somewhere between 600 and 900 °C depending on purity and surface treatment.

The same packing difference sets the optical constants. Rutile has a refractive index of about 2.70 against roughly 2.55 for anatase — a small gap on paper, but scattering power rises steeply with refractive index, so rutile hides better at equal loading. Rutile is also denser, around 4.2 g/cm3 versus about 3.9 g/cm3 for anatase, which matters when you formulate by volume.

Rutile vs Anatase at a Glance

Property Rutile Anatase
Refractive index ~2.70 ~2.55
Density (g/cm3) ~4.2 ~3.9
Hiding power Higher Lower
Photocatalytic activity Lower Higher
Outdoor weathering Strong Chalks faster
Undertone Neutral, slightly warm Bluer white
Hardness (Mohs) ~6–6.5, more abrasive ~5.5–6, gentler

Most pigment grades of either form are milled to particle sizes around 0.2–0.35 μm, close to half the wavelength of visible light, where scattering peaks. The values above are typical handbook figures; treat them as orientation, because silica and alumina surface treatments shift real-world performance grade by grade.

Treated grades deserve a note of their own. Coating rutile particles with a few percent of silica and alumina, a standard step in modern production, lowers photocatalytic activity further and helps the pigment disperse in alkyd and acrylic binders. Untreated surfaces, by contrast, can interact with hindered amine light stabilizers in plastics, so film and rigid PVC masterbatch recipes commonly specify alumina-treated types.

Both grades sit inside a broader whites-to-colors program. Ningbo Ultra Color Co., Ltd. is a pigment and dye supplier whose range runs from titanium dioxide and other inorganic whites through organic pigments, solvent dyes, effect pigments and additives. Every order is checked against REACH and RoHS requirements, and retained batch samples are kept on file for over five years.

Which Grade for Which Job

Rutile when the part lives outdoors

Exterior paint, coil coating, PVC window profiles, automotive refinishing: these call for rutile. Its tighter lattice absorbs UV and its lower photocatalytic activity spares the binder, so the film keeps its gloss far longer. An unmasked anatase under strong sun does the opposite — the surface slowly degrades and the coating chalks. Thin-film work follows the same logic: quality offset inks build opacity inside a dried film only a few micrometers thick, so they rely on fine rutile with a d50 near 0.2 μm.

Anatase when softness and tone come first

Paper delustering, polyester fiber spinning lines that run near 290 °C, interior emulsion paint, and self-cleaning photocatalytic coatings favor anatase. It is softer and less abrasive on processing equipment, gives a distinctively blue, cool white, and its higher photocatalytic activity is a feature rather than a defect in air-purifying or self-cleaning formulations.

Picking a white pigment is really a question of particles versus dissolved colorants, not just which white. If that distinction is new to you, the primer on pigment versus dye differences covers how each behaves in a resin or vehicle.

Frequently Asked Questions

Is rutile titanium dioxide always the better grade?

No. Rutile wins on hiding power and weathering, so it dominates paints and plastics for outdoor use. But anatase still outsells it for paper, fibers and photocatalytic work, where its softer particles, bluer tone and higher photo-activity fit better, often at a lower price.

Why does anatase chalk faster outdoors?

Anatase is the more photo-active lattice. Under UV it generates reactive species that oxidize the organic binder around the pigment particles, and the film surface erodes into a chalky layer. Rutile absorbs UV with far less of this catalytic effect, and surface-treated rutile grades suppress it further.

Can I mix rutile and anatase in one formulation?

Yes, and formulators do. A common move is blending to balance cost against durability, or adding anatase to push a white cooler in tone. Keep total TiO2 loading in mind: in paint, titanium dioxide commonly makes up somewhere between 10 and 30 percent of the dry film volume, depending on gloss level.

Scroll to Top