One chemistry, six commercial colors

Iron oxide pigments are the workhorse of the color industry: nearly all of them are compounds of iron and oxygen, yet they span red, yellow, orange, brown, green and black. Red is hematite, α-Fe2O3, listed as Pigment Red 101 (Color Index 77491). Yellow is goethite, α-FeOOH, Pigment Yellow 42 (77492). Black is magnetite, Fe3O4, Pigment Black 11 (77499). Three crystal structures, one element, six saleable shades.

The reason these pigments sit in concrete, roofing, plastics and coil coatings is stability. Blue wool light fastness sits at the top of the scale, typically rated 8. Hematite has a refractive index around 3, which gives red oxide strong hiding power at low dose. UV, rain and most chemicals leave the crystal lattice untouched. A dye would fade or bleed in the same exposure, which is the core of the difference between pigments and dyes.

Iron oxide red holds the most heat

PR101 is the most heat-tolerant shade of the family. It commonly holds its color to around 500 °C, which is why brick, ceramic and roof-tile makers use it as the default red. Processing at extrusion or calcination temperatures does not shift the shade.

Particle size is the tuning knob. Grades around 0.1 to 0.2 µm look bright and yellowish red; grades near 1 µm look deep and bluish red. Same chemistry, different shade position, so a supplier list such as the one on the iron oxide pigment page carries several reds rather than one. When a paint line needs a cleaner, brighter red than oxide can reach, organic grades like the ones compared in DPP reds PO73 and PR254 take over, at the cost of some weather resistance.

Yellow, orange and brown: the dehydration ceiling

Yellow oxide is goethite, and goethite carries water in its crystal. Heat it to roughly 200 to 260 °C and the water leaves, converting the crystal to red hematite. That is the whole story of the yellow shade ceiling, and the failure mode is not fading but a color change to red or orange brown.

Orange oxide is usually lepidocrocite, γ-FeOOH, or a blend of red and yellow oxide; the blend route dominates commercial grades. Brown, Pigment Brown 6, is typically a controlled mix of red, yellow and black oxides with a heat ceiling around 300 °C. Wood coatings and translucent timber stains lean on these shades because the earth tones survive sunlight for decades.

Black is magnetite, and green is a composite

Black oxide is magnetite, PBk11, stable to around 300 °C. Push it hotter in air and it oxidizes toward brown, so high-temperature processing needs the red grade instead. Black oxide is the color of choice in gray concrete and dark engineering plastics, where tinting strength per gram matters more than a pure jet black.

Green is the odd one. There is no simple green iron oxide crystal; commercial green oxide is a composite of yellow iron oxide and an organic blue, usually a phthalocyanine. Its heat ceiling therefore follows the yellow component, commonly around 200 °C. This is also why green grades list a light fastness one step below the pure oxides: the blue half is excellent, but not literally rock-class.

Six colors from one supplier read as one system, not six purchases. The iron oxide line at Ningbo Ultra Color covers red, yellow, orange, brown, green and black for plastic and coating uses, with REACH SVHC and RoHS checks on every lot and a sample of each batch retained for five years.

The palette in one table

Color Color Index Chemistry Typical heat limit Main outlets
Red PR101 / 77491 α-Fe2O3 (hematite) ~500 °C Brick, roofing, ceramics, coil coating
Yellow PY42 / 77492 α-FeOOH (goethite) 200–260 °C Construction, road paint, plastics
Orange blends γ-FeOOH or red-yellow blend ~200–250 °C Coatings, masterbatch
Brown PBr6 red-yellow-black blend ~300 °C Wood coatings, timber stains
Green composite yellow oxide + phthalocyanine blue ~200 °C Coatings, garden and camouflage tones
Black PBk11 / 77499 Fe3O4 (magnetite) ~300 °C Gray concrete, engineering plastics

Values above are typical industry ranges, not a single supplier’s spec sheet; exact limits move with particle size and surface treatment. The site’s own grade list and its application industries pages are the reference for what a given producer actually stocks.

Frequently asked questions

Which iron oxide color stands the most heat?

Red, by a wide margin. Hematite, PR101, commonly holds to around 500 °C, while yellow and green grades dehydrate or lose their blue component at roughly 200 to 260 °C. Any process above 300 °C should specify red oxide.

Why does my yellow oxide turn red during processing?

Goethite loses its crystal water between about 200 and 260 °C and converts to red hematite. The shift is a phase change, not degradation. Lower the process temperature, or accept the warmer shade and correct the formula toward yellow before extrusion.

Is iron oxide green a pure iron oxide?

No. It is a composite of yellow iron oxide and an organic blue pigment, usually phthalocyanine blue. That is why its heat ceiling tracks the yellow component and its light fastness, typically 7 to 8 on the blue wool scale, sits just under the pure oxides.

Scroll to Top