Bleaching never finishes the job on its own. Even fully bleached cotton keeps a faint cream tone, and gray polyester knit only looks white after finishing. Optical brighteners close that gap. Dosed well below one percent, they convert invisible ultraviolet light into a faint blue-violet glow, and the fabric reads as brilliant white rather than merely clean.
Why Bleached Fabric Still Looks Yellow
The chemistry is the same family described in the guide to optical brighteners in plastics: fluorescent molecules that absorb around 340-380 nm and re-emit near 420-440 nm as blue-violet light. That emission cancels the yellow undertone of the fiber, so measured whiteness rises with no pigment film involved.
What changes on textiles is delivery. A molded part carries its brightener locked inside a melt. Fabric sits in water, so the molecule must travel out of the liquor onto the fiber, which splits the product world into three families: water-soluble stilbene types with direct affinity for cellulose, disperse types that dye polyester the way disperse dyes do, and high-melting benzoxazole grades such as OB-1, KSN, KCB and KSB, listed in the same additives catalog for melt spinning and high-heat work. The first family never shows up in a plastics catalog. The other two serve both trades.
Match the Chemistry to the Fiber
Two questions drive selection: which fiber, and which application route the mill actually runs. The ranges below are typical starting points from common industry practice, not a substitute for the supplier’s own figures; confirm each value before a production run.
| Fiber | Brightener family and common grades | Application route | Typical starting dose |
|---|---|---|---|
| Cotton, viscose, lyocell | Water-soluble stilbene types (VBL, CBS-X class) | Exhaust or pad, often inside the peroxide bleach bath | 0.1-0.6% owf exhaust; 2-8 g/L pad |
| Polyester fabric and yarn | Disperse types (ER class, with KSN and KCB in related roles) | High-temperature exhaust at 130°C, or pad-thermofix at 180-210°C | 0.15-0.5% owf; 2-6 g/L |
| Polyester and polyamide melt spinning | OB-1, yellow and green shades | Dosed into chip or melt before extrusion | 200-500 ppm on polymer |
| Nylon and wool | Pyrazoline and other acid-affinity types | Acid bath, pH 4-5, at 95-100°C | 0.1-0.5% owf |
| Acrylic | Cationic types | Exhaust at 80-95°C | 0.1-0.4% owf |
Cellulose: exhaust, pad, or the bleach bath
Stilbene brighteners behave like direct dyes. They exhaust from a hot bath held around 60-80°C for 20-30 minutes, and a dose of salt pushes uptake the same way it does for dyeing. Many mills fold the product straight into the peroxide bleach bath to save a step, which works because these molecules tolerate hydrogen peroxide. Hypochlorite is the enemy. Chlorine attacks the stilbene core, and a combined chlorine step can leave a yellow deposit instead of whiteness, so chlorinated goods get a separate brightener bath after rinsing.
Synthetics: heat sets the route
A polyester article can go white three ways. High-temperature exhaust at 130°C treats the brightener like a disperse dye and suits packages, beams and garments. Pad-thermofix, roughly 30-60 seconds at 180-210°C, fits continuous open-width lines. Fiber producers take the third path and dose OB-1 into the melt at 200-500 ppm, so every filament ships pre-whitened. KSN and KCB cross between fabric and fiber roles, which is why their grade-by-grade behavior matters on both sides of the industry.
Dosage, Failures, and the Paperwork
More brightener stops helping at a ceiling. Crowd the molecules onto one fiber and they start re-absorbing their own emission; whiteness flattens, then drifts greenish yellow, and no extra dose reverses it. The cure is subtraction. Cut the dose by 30-50% and the blue-violet balance usually comes back.
Sunlight sets a second limit. These molecules absorb UV, and on cellulose that absorbed energy can accelerate fiber damage, a failure finishers call phototendering. Goods destined for strong daylight exposure run at the low end of the range and pair the brightener with a UV absorber, trading a little first-day whiteness for strength retention. Judge every trial under D65 light with defined UV content, never under ceiling LEDs, and report CIE whiteness values instead of adjectives.
Compliance closes the file. Textile buyers increasingly ask colorant suppliers about OEKO-TEX 100 capability alongside REACH SVHC screening, and the textile section of the application overview states the product range can meet OEKO-TEX 100. Ningbo Ultra Color Co., Ltd supplies dyes, organic and inorganic pigments, effect pigments and additives to customers in the plastic, ink, coating and textile industries; the additives listing runs from OB-1 in two shades through OB, FP127, KSN, KCB and KSB. REACH SVHC and RoHS checks apply to every batch, and retained samples are kept for five years.
FAQ
How much optical brightener does cotton fabric need?
Typical exhaust recipes run 0.1-0.6% owf, and padding liquor sits near 2-8 g/L. Start at the bottom of the range, measure CIE whiteness after each step, and stop at the last step that still gains. The optimum almost always lands below 0.5% owf.
Why did my whitened fabric turn green?
Overdosage, in most cases. Concentrated brightener molecules re-absorb their own blue-violet emission, and the shade tips toward greenish yellow. Cut the dose by a third and retest before reaching for a violet tint, which only masks the imbalance.
Can plastic grades like KSN or KCB whiten polyester fabric?
Yes, when heat is available. At 130°C exhaust or 180-210°C thermofix they behave like disperse dyes and build solid whiteness on polyester. OB-1 belongs to the melt route and will not exhaust from a bath, while the water-soluble cotton types simply wash off polyester.


