A chrome-bright can finish, a silver ink on a foil label and a hammer-tone paint all start from the same raw material: microscopic aluminum flakes. Coatings formulators meet those flakes in two commercial forms, dry silver powder and silver paste, and the choice shapes the whole production line downstream. This comparison sets out the differences, explains leafing behavior, and separates aluminum from the glitter and pearl effects it so often gets confused with.

What an aluminum pigment actually is

Aluminum pigments are flake pigments, not round particles. Producers make them by ball-milling aluminum grit in the presence of a fatty-acid lubricant, which flattens the metal into platelets a fraction of a micrometer thick and several micrometers across. Coating grades commonly sit at a D50 of around 5–30 µm: fine flakes give a smooth satin silver, while coarse flakes throw a brighter, sparklier metallic glare.

Because every platelet is a tiny mirror, the pigment delivers opacity and white brightness at the same time. Our effect pigment catalog lists the aluminum silver powder line as suitable for paints, inks and plastics, with excellent hiding power and white brightness, and the same flake logic carries into each downstream formula.

Silver powder vs silver paste

The two forms share one flake and differ in everything after the mill. Dry powder is essentially 100% metal. Paste carries identical flakes inside a mineral-spirit-type carrier, typically at 60–80% solids, pre-wetted so it stirs straight into a coating vehicle.

Property Aluminum silver powder Aluminum silver paste
Physical form Dry, free-flowing metallic flakes The same flakes dispersed in a solvent carrier
Solids content Essentially 100% metal Typically 60–80%
Dispersion route Wetted under high shear at the disperser; dust control mandatory Pre-wetted, stirs directly into solvent-borne vehicles
Leafing orientation Supplied in leafing and non-leafing grades Same grade choice; leafing types common in silver inks
Typical uses Powder coatings, masterbatch, high-solids industrial paint Automotive refinish, coil and can coatings, printing inks

Why pastes exist

Safety comes first. Fine aluminum dust ignites with spark energies of only a few millijoules, so dry powder demands grounded, explosion-vented handling that many paint shops simply do not have. A paste removes most of that hazard and adds a formulation benefit: pre-wetted flakes disperse without the agglomerates dry powder forms the moment it meets a binder. For solvent-borne industrial coatings and printing inks, paste is the default. Powder coatings and plastic masterbatch, where carrier solvents are unwelcome, take the dry grade, a split that repeats across the application fields for coatings and inks from can lacquers to masterbatch.

Leafing and non-leafing grades

Orientation decides the look. Leafing flakes are treated with stearic acid, which lowers their surface energy so they float to the air interface of the drying film and pack into the top 1–2 µm of the coating, aligned parallel to the surface. The result is a continuous silver mirror with real barrier value, the classic finish of silver-drum paint and roof coatings. Non-leafing grades carry an oleic-type treatment instead, stay distributed through the film, and read as a softer metallic sheen that pairs with transparent colorants. That is why automotive basecoats are almost always non-leafing: the flake gives sparkle, the colorant gives hue.

Aluminum, glitter or pearl?

Three effect families get conflated constantly, yet they run on different physics. Glitter is cut rather than milled: precision-slitted film flakes, commonly 100–600 µm across, whose flat facets give a hard, discrete sparkle. Aluminum pigments are ball-milled metal platelets an order of magnitude finer, producing continuous luster rather than isolated glints. Pearl pigments build their effect by interference, with mica or glass platelets coated in oxide layers tens to hundreds of nanometers thick. The distinctions matter at the scale of purchase, and a fuller treatment of the third family sits in our article on pearl pigments in coatings.

Frequently asked questions

Which hides better, silver powder or silver paste?
Hiding is a flake property, not a form property. Both products carry the same platelets, so opacity tracks the D50 and the leafing treatment rather than dry versus pasted. Dispersion quality moves the result more than the commercial form does.

Can aluminum pigments produce a colored coating?
Not on their own. Aluminum reflects rather than absorbs, so hue has to come from a transparent pigment or dye sharing the film. Catalog entries such as glitter gold aluminum silver powder cover the gold direction, but a true red or blue metallic still needs a transparent colorant alongside the flakes.

Do aluminum pigments work in waterborne coatings?
With the right surface treatment. Untreated flakes react with water and gas, so aqueous systems call for passivated, silica-encapsulated grades and pastes built on aqueous carriers. A solvent-borne paste dropped into a water formula loses brightness and can build pressure in the container.

Ningbo Ultra Color Co., Ltd supplies effect pigments alongside solvent dyes, organic and inorganic pigments and additives for coating, ink, plastic and textile customers. Every raw material batch is tested, retention samples are kept for five years, and REACH SVHC and RoHS checks support each shipment.

Scroll to Top