Coloring engineering plastics is a filtering exercise. PS, ABS, PC, PET and PA6 span roughly 100 °C of melt temperature, and a colorant that shines in one hopper can gas off or drift in another. Resin chemistry sets the second filter: a dye that dissolves in styrenics can bloom back out of nylon.

Melt temperature sets the floor

Injection molders typically run PS at 200–250 °C and ABS at 220–260 °C, PA6 around 240–280 °C, PET around 260–290 °C, and PC at roughly 280–320 °C. A dye rated for 260 °C service holds its shade through a styrene melt, then shifts or volatilizes where PC lives.

Heat stability is the first column to read in coloring engineering plastics. The dye catalog lists a measured figure for each of its 72 solvent dyes, next to a resin suitability matrix. Counting marks tells the story fast: 70 dyes carry a full PS rating, 36 a full PC rating, 33 for PET, 11 for PA6. The 62 organic pigments narrow the same way: only 12 full PC marks. The full colorant portfolio shows both matrices.

PS and ABS, the comfortable end

Styrene melts forgive almost everything. Some 70 of the 72 catalog dyes hold a full PS mark, including inexpensive monoazo types like Solvent Yellow 14, rated 260 °C with 5–6 light fastness. Its ABS and PC columns are blank, which hardly matters at 230 °C in PS.

ABS sits one step up. It awards full marks to 42 dyes, lists 20 more as limited, usable after evaluation in your own compound, and rejects 10. The pigment side is friendlier: the quinacridone Pigment Red 122 (300 °C, light fastness 8) carries full PS and ABS marks, as does the benzimidazolone Pigment Yellow 181 (300 °C, 8). Both stop at the styrenics.

PC, PET and PA6, where the list shortens

Move past 280 °C and the dye table turns into anthraquinone country. Six of the nine dyes holding full marks in all five resins are anthraquinones: Solvent Red 52, Solvent Red 149, Solvent Blue 97, 122 and 132, and Solvent Green 28, every one rated at 300 °C. A quinoline, Solvent Yellow 157 (300 °C, 6–7), and an indandione, Solvent Yellow 176 (300 °C, 7–8), complete the group, along with the perinone Solvent Red 179.

PA6 is the narrowest gate. It gives full marks to 11 dyes only, and nine of those 11 sit at the 300 °C tier. Nylon rewards chemistry built for the top of the range. Among pigments, the phthalocyanines dominate: Pigment Blue 15:1, 15:2, 15:3 and 15:4 each hold 300 °C, light fastness 8 and full marks in all five resins, with the nickel azo Pigment Yellow 150 (300 °C, 8) as the only yellow in that club.

A red for every engineering resin

Reds show the pattern best. Solvent Red 52, an anthraquinone at 300 °C and blue wool 6–7, carries full marks from PS to PA6, which is why it anchors so many engineering shade cards. The classic disazo reds Solvent Red 24 and 27, rated 260 °C and 250 °C, go blank in the PC, PET and PA6 columns; why SR 24 and SR 27 stop at the engineering resins comes down to those two numbers.

Pigment reds split the same way. The quinacridone Pigment Red 202 (300 °C, light fastness 8) covers PS, ABS, PET and PA6 but leaves PC blank, while the anthraquinone Pigment Red 177 (300 °C, 8) fills PC and PA6 with only a limited mark in ABS. DPP reds keep their outdoor durability, yet Pigment Red 254 (300 °C, light fastness 8) takes a full PS mark while the whole DPP family stays out of polycarbonate.

The shortlist in one table

Dye and pigment figures are catalog-measured heat stability and blue wool light fastness; melt windows reflect typical molding practice. The industry applications pages break resin families down further.

Resin Typical melt window Dye shortlist Pigment shortlist
PS 200–250 °C Solvent Yellow 14 (260 °C, 5–6) Pigment Red 122 (300 °C, 8)
ABS 220–260 °C Solvent Yellow 98 (300 °C, 6–7) Pigment Yellow 181 (300 °C, 8)
PC 280–320 °C Solvent Green 28 (300 °C, 6–7) Pigment Blue 15:3 (300 °C, 8)
PET 260–290 °C Solvent Blue 97 (300 °C, 6–7) Pigment Yellow 147 (300 °C, 7)
PA6 240–280 °C Solvent Yellow 157 (300 °C, 6–7) Pigment Red 202 (300 °C, 8)

Every entry holds a full catalog mark in the resin of its row.

Frequently asked questions

Which colorants cover all five resins?

Nine dyes and five pigments. On the dye side: Solvent Yellow 157 and 176, Solvent Red 52, 149 and 179, Solvent Blue 97, 122 and 132, and Solvent Green 28. On the pigment side: Pigment Yellow 150 plus Pigment Blue 15:1 through 15:4. All fourteen sit at 300 °C heat stability, so one inventory can serve every hopper.

Why does PA6 accept so few dyes?

Heat and chemistry together. PA6 typically melts hot enough to weed out mid-tier stability, and its amide chemistry is a poor host for many soluble dye molecules, so shades tend to bloom. The catalog reflects it: 11 full marks out of 72 dyes. Insoluble pigments sidestep the issue, and PB 15:1 to 15:4 with PY 150 are the safe calls.

Can one red masterbatch serve both ABS and PC?

Not if it was built for ABS alone. The two melts sit about 60 °C apart at the top end, and a 260 °C red will drift in PC. Solvent Red 52 spans both resins with full marks, and Pigment Red 177 covers PC fully with a limited mark in ABS, so pick the letdown ratio accordingly.

Working with a specialized colorant supplier

Ningbo Ultra Color supplies solvent dyes, organic and inorganic pigments, effect pigments and additives for plastic, ink and coating customers. Every batch is checked against updated REACH SVHC and RoHS limits, and batch samples are kept for five years, so any shade dispute can be settled against physical material.

Scroll to Top