A photoluminescent pigment is a powder that stores light and pays it back slowly. Charged for ten minutes under daylight or a lamp, it glows green for hours after the room goes dark. The photoluminescent pigment listing on this site describes it as a light-storage powder that absorbs various visible light under 450 nm and can be reused many times, so one batch keeps cycling for years. The same powder goes into coatings, inks, paints, plastics, printing paste, ceramics and glassware.
How a Photoluminescent Pigment Stores Light
Glow pigments work by phosphorescence. A photon from sunlight or a lamp lifts an electron inside the crystal lattice of a pigment grain. Ordinary fluorescence lets the electron drop back within nanoseconds. Phosphorescent crystals hold on. Strontium aluminate doped with europium and dysprosium, written SrAl2O4:Eu,Dy, traps the excited electron in lattice defects created by the dopant ions, and those electrons leak back to the ground state over minutes to hours. That slow leak is the afterglow you see.
The numbers separate one grade from the next. Excitation is strongest below about 450 nm, so daylight and cool-white LEDs both charge the powder efficiently. Emission for the common blue-green grades peaks around 520 nm, close to the peak sensitivity of the dark-adapted eye, which stretches perceived brightness. Quality strontium aluminate grades typically stay perceptible for 8 to 12 hours, measured down to the 0.32 mcd/m² endpoint defined in DIN 67510, the standard commonly used to compare afterglow pigments.
Strontium Aluminate vs. Zinc Sulfide
Two chemistries dominate the market. Zinc sulfide doped with copper, ZnS:Cu, is the older and cheaper system, while strontium aluminate powers modern long-glow products. The usual trade-offs:
| Property | Strontium aluminate (typical) | Zinc sulfide (typical) |
|---|---|---|
| Afterglow to the visibility limit | around 8–12 hours | around 30–60 minutes |
| Initial brightness | commonly near 10× zinc sulfide | reference level |
| Body color in daylight | pale yellow-green | pale gray-white |
| Moisture behavior | raw powder slowly hydrolyzes; silica-coated grades suit waterborne systems | more tolerant of water |
| Typical particle grades | around 20–80 µm | often finer |
Particle size drives most purchasing decisions. Coarse grains glow brighter because they carry fewer crystal boundaries per unit mass, while fine grades disappear into thin ink films at the cost of afterglow. Dosage matters just as much: formulators commonly load 10–30% by weight into resin or paint, and safety markings sit near the top of that range.
Not every effect pigment earns its keep through sparkle. Ningbo Ultra Color Co., Ltd supplies photoluminescent pigment alongside aluminum silver powder, glitter and pearl pigment, checks every batch against REACH SVHC and RoHS limits, and keeps batch samples for more than five years so any lot can be traced back.
Where Photoluminescent Pigments Work Best
Safety leads the list. Fire emergency systems are named among the target applications on the product page, and photoluminescent evacuation signage is the highest-value use of the material: wayfinding lines and exit signs that keep working through a power cut. Signage inks are usually screen printed in thick films and dosed near 20–30% pigment to meet the class requirements of DIN 67510 or the ISO 17398 sign standard often cited in tenders.
Plastics come next. Compounded into masterbatch, compounds and 3D-printing filament, the powder turns switch plates, instrument housings and camping gear into objects that glow all night. Consumer goods and decorations are both named as target sectors on the product page, and military facilities and communication and transportation equipment round out the official list.
Inks, paints and coatings complete the field. Screen inks for textiles and labels favor coarse grades; waterborne wall paints need the silica-coated types; ceramics and glassware decorators draw on the same powder. Dispersion and film thickness decide the result more than chemistry does.
FAQ
How long does a photoluminescent pigment glow after charging?
Ten minutes under ordinary room light is a common charge for a quality strontium aluminate grade. The glow runs brightest in the first hour, decays quickly, then flattens into a long tail that a dark-adapted eye can follow for typically 8 to 12 hours. Zinc sulfide grades reach the same visibility limit in roughly 30 to 60 minutes.
Can photoluminescent pigment go into water-based paint?
Raw strontium aluminate slowly reacts with water and loses brightness, so waterborne systems call for silica-coated, water-resistant grades. Stir the powder in shortly before application rather than storing the mixed paint for weeks, and avoid iron mixing tools, which are commonly reported to dull the glow.
How much photoluminescent pigment should I add per kilogram?
Formulators commonly work between 100 and 300 g per kilogram of resin or paint, which equals 10–30% by weight. Novelties and decorative prints sit near the bottom of that range, safety signage near the top. Below about 10% the glow turns spotty, because the grains sit too far apart to read as a continuous line.


