One Macrocycle, Two Halogens

Phthalocyanine green is the most durable green pigment family in industrial use, and it comes in two commercial versions. Pigment Green 7 is the chlorinated form: a copper phthalocyanine core with chlorine atoms on the outer benzene rings. The sixteen replaceable hydrogen positions on that skeleton can all take halogen, and commercial PG7 typically carries chlorine on fourteen to fifteen of them. Pigment Green 36 is the brominated counterpart, and many commercial grades retain a little chlorine alongside the bromine.

That single substitution sets the two greens apart. Bromine is a larger, heavier atom than chlorine, roughly 79.9 against 35.5 on the atomic mass scale, and it shifts the way the molecule absorbs light. The result is a visible shade split: PG7 reads as a blue-shade green, while PG36 runs distinctly yellower. Same macrocycle, same copper center, different color direction.

Both pigments inherit the family toughness. They are built on the same skeleton as the phthalocyanine blue PB 15 grades, which is why their fastness numbers sit at the top of the organic range rather than the middle.

What the Measured Table Shows

The organic pigment table behind our organic pigments catalog carries measured rows for both greens, and the numbers land closer than most buyers expect:

Pigment Halogen Heat stability (°C) Light fastness Migration, FS 0.1% PET PA 6
Pigment Green 7 Chlorine 300 7–8 5 ● ○
Pigment Green 36 Bromine 300 7–8 5 ○ ○

Read the shared numbers first. Both greens measure 300°C heat stability, which is the ceiling of the test scale rather than a failure point, as the organic pigment heat stability guide explains. Light fastness is 7–8 for both, and migration at 0.1% full shade reaches the top mark of 5. The resin matrix is where the two rows part company: PG7 is rated suitable for PET, while PG36 is rated limited there. Every other column matches, including suitable ratings in PVC, PE/PP, PS, ABS, PC, rubber, PUR and PP fibers, and limited ratings in PET fibers and PA fibers.

Shade, Cost, and Where Each One Lands

Selection between the two is usually decided by shade target and budget. PG7 is the volume workhorse of green colorants, covering inks, coatings and the bulk of plastic coloration wherever a clean blue-shade green is acceptable. PG36 is the choice when the target sits yellower, in the fresh grass to teal territory that PG7 cannot reach by dosage alone. Tricking PG7 toward yellow with a mixed pigment often costs more fastness than the premium for PG36 would have.

Price follows scarcity. Fewer plants run bromine chemistry, and the raw material is more expensive, so PG36 typically commands a clear premium over PG7. Buyers who only need the yellow direction in a low-demand shade sometimes accept that cost in small lots; high-volume compounders more often re-engineer the shade around PG7.

Electrical behavior deserves one caution. Good grades of both greens are essentially non-ionic, which is why phthalocyanine greens commonly appear in PVC wire insulation without raising conductivity, and nothing in the chemistry gives one grade a systematic electrical edge over the other. But neither pigment can enter a halogen-free specification. Chlorine or bromine is the entire basis of these molecules, so cable and connector compounds specified low-halogen need a different green altogether.

Working with a specialized supplier keeps the comparison grounded. Ningbo Ultra Color Co., Ltd lists both Pigment Green 7 and Pigment Green 36 in its organic pigment catalog. Every batch is tested before release, REACH and RoHS compliance is verified, and retain samples are kept for five years. The table above comes from that same measured catalog.

FAQ

Is Pigment Green 36 more heat stable than Pigment Green 7?

No. Both grades measure 300°C in the catalog table, with light fastness of 7–8 and top-mark migration resistance. The difference between them is shade and price, not fastness class. Neither will outlast the other in a standard polyolefin molding test.

Which one is the bluer green, PG7 or PG36?

PG7 is the blue-shade green. Swapping chlorine for the heavier bromine atom in PG36 shifts absorption and moves the shade visibly toward yellow. If the target color card sits between a deep blue-green and a fresh yellow-green, the two grades bracket it from opposite sides.

Can either grade be used in halogen-free compounds?

No. Both pigments are halogenated by definition, chlorine in PG7 and bromine in PG36, so neither belongs in a halogen-free or low-halogen specification. Formulators facing that constraint typically move to inorganic greens such as chromium oxide or cobalt green, accepting a different shade space.

Scroll to Top