Anthraquinone chemistry carries most of the heat-tolerant color in a solvent dye program. All 29 anthraquinone grades in the dye table on this site measure between 230 °C and 300 °C for heat stability, and the best of them pair a 300 °C rating with 7–8 light fastness. Few other dye classes hold that combination. The reasons sit in the molecule, and they show up reliably in the resin columns.
The anthraquinone core
The parent molecule is anthraquinone itself: three fused six-membered rings with carbonyl groups at the 9 and 10 positions. In pure form it is a pale crystalline solid, the golden needles shown in the image above. Dye chemistry begins when amino, hydroxy or alkylamino substituents attach to the outer rings, because those groups shift light absorption across the visible spectrum and give each commercial grade its hue.
The fused-ring system is rigid and flat. Color chemists commonly credit that rigidity, together with the absence of an azo nitrogen-to-nitrogen linkage, for the family’s resistance to thermal and photochemical attack: incoming energy spreads over a stiff aromatic skeleton instead of concentrating on one cleavable bond. The claim is a general one. The measured table backs it anyway, grade by grade.
Shade range from yellow to green
Two yellows open the list. Solvent Yellow 33 measures 290 °C with 5–6 light fastness, while Solvent Yellow 163 reaches 300 °C and 7–8, the strongest light rating in the family. A single orange follows, Solvent Orange 86 at 280 °C. Six reds come next, from Solvent Red 146 at 290 °C to Solvent Red 52, 111, 149, 168 and 207, all flat at 300 °C.
Blues dominate. Eleven of the 29 rows carry blue names, from Solvent Blue 35 and the long-serving Solvent Blue 36 through to Solvent Blue 132, and the deep-water end of that group is where anthraquinone earns its reputation: Solvent Blue 97 and Solvent Blue 104 both measure 300 °C, the latter with 7–8 light fastness. Five violets and four greens complete the set. Solvent Green 28 runs 300 °C with 6–7 light fastness and holds a solid mark in every application column on the site, nylon included.
Behind the measured table
Ningbo Ultra Color supplies the anthraquinone range above alongside organic and inorganic pigments, effect pigments and additives. REACH SVHC and RoHS screening applies to every lot, each batch of raw material is tested, and batch samples are kept for five years, so any figure quoted here can be traced to the lot that shipped.
Heat stability where it counts
The pattern in the numbers is tight. Twenty-seven of the 29 measured grades hold 280 °C or better, and 20 sit at a flat 300 °C. For contrast, the disazo reds stop lower: Solvent Red 24 measures 260 °C and Solvent Red 27 measures 250 °C, and both carry crosses in the polycarbonate, PET and nylon columns, while Solvent Red 52, an anthraquinone, posts solid marks in all eleven application columns at 300 °C. For a measured walk through two reds, the Solvent Red 24 versus Solvent Red 27 comparison lays out the disazo ceiling in detail.
Two exceptions keep the claim honest. Solvent Blue 36 measures 240 °C with 4–6 light fastness, and Solvent Violet 8 measures 230 °C, with its solid marks limited to oil, paint and ink systems. Neither grade belongs in an engineering-resin process window, and neither is sold as if it does.
| Grade | Chromophore | Heat stability | Light fastness | Notes from the site table |
|---|---|---|---|---|
| Solvent Yellow 33 | Anthraquinone | 290 °C | 5–6 | Solid in PS and PMMA; crosses in PC, PET, PA.6 |
| Solvent Red 52 | Anthraquinone | 300 °C | 6–7 | Solid mark in all eleven application columns |
| Solvent Blue 104 | Anthraquinone | 300 °C | 7–8 | Solid in PC and PET; partial in nylon |
| Solvent Green 28 | Anthraquinone | 300 °C | 6–7 | Solid in every column including PA.6 |
| Solvent Blue 36 | Anthraquinone | 240 °C | 4–6 | Family exception on the low side |
| Solvent Red 24 | Disazo | 260 °C | 5–6 | Crosses in PC, PET and PA.6 |
| Solvent Red 27 | Disazo | 250 °C | 6–7 | Crosses in PC, PET and PA.6 |
Once the resin window is fixed, picking solvent dyes for a masterbatch carrier comes down to reading these same columns against the carrier resin, because a dye that crosses out in PET will cross out in a PET-based masterbatch just as fast.
Frequently asked questions
Why do anthraquinone dyes survive 300 °C when many azo reds stop near 260 °C?
The rigid fused-ring skeleton disperses thermal energy without a single weak linkage, a mechanism color chemists describe in general terms. The site numbers agree with it: Solvent Red 52 holds 300 °C while the disazo Solvent Red 24 and 27 hold 260 °C and 250 °C.
Which anthraquinone grades work in polycarbonate, PET and nylon?
Solvent Red 52, Solvent Blue 122, Solvent Blue 132 and Solvent Green 28 carry solid marks across PC, PET and PA.6. Solvent Blue 104 is solid in PC and PET with a partial mark in nylon, so confirm the resin before specifying it.
Are there anthraquinone dyes that do not reach 280 °C?
Two. Solvent Blue 36 measures 240 °C and Solvent Violet 8 measures 230 °C, with the violet rated for oil, paint and ink systems rather than thermoplastics. Every other anthraquinone in the table measures 280 °C or higher.


