An exposed LED chip is painful to look at. Fixtures hide it behind a cover of polycarbonate (PC), PMMA or polystyrene (PS), and that cover almost always contains a light diffusion agent: micron-scale polymer microspheres dispersed in the melt that scatter rays sideways until the point source reads as a soft, even glow. Lamp shades, tube covers, panel diffusers and LCD light guide plates all lean on the same trick. What follows: the mechanism, the dosage math, and the fit across PC, PMMA and PS.
What a light diffusion agent actually does
Commercial diffusion agents are cross-linked spherical beads, either silicone (polymethylsilsesquioxane) resin powder or acrylic microspheres. Silicone grades come in tight steps from 1 to 5 µm; acrylic beads span roughly 3 to 30 µm. Dispersed at a fraction of a percent, they sit in the resin with a refractive index different from the matrix. That gap is the whole trick. PC and PS hold indices near 1.59 and PMMA near 1.49, while silicone beads measure 1.42 to 1.45. Every bead boundary bends a ray, so light leaves the cover spread over a wide angle instead of beaming straight through. Silicone suppliers place the useful window for the bead-to-resin index ratio at roughly 0.91 to 0.97: close enough to transmit, far enough to scatter.
Narrow particle size distribution is the first spec buyers check: uneven bead sizes print visible blotches across a panel, while tight cuts keep the halo uniform.
The transmittance and haze trade-off
Two numbers describe a diffuser, both measured under ASTM D1003: total transmittance, the light that gets through, and haze, the share of transmitted light scattered more than 2.5 degrees off axis. They pull against each other. Each event redirects light, and some is absorbed or bounced back. More agent buys more haze and hides the LED better, but the fixture dims. Inorganic fillers such as barium sulfate or silica show the failure mode: they scatter hard and can drag a lampshade below the 50 percent transmittance many shade specs set as a floor. Organic beads lose far less light at equal softness.
How much diffusion agent to add
Dosage decides where you land. PC bulb and lamp covers typically start at 0.3 to 0.5 wt% silicone agent, and loadings beyond about 2 wt% rarely pay off, because the transmission penalty compounds faster than the haze gain. Particle size tunes the same balance: a 5 µm grade reaches a given haze at lower loading than a 2 µm grade, since each larger bead scatters more. Coarse beads carry a cost. In a 1 mm light guide plate they leave streaks along the flow direction, so plate makers lean fine, and a 1.5 µm grade is a common pick at that thickness. Thicker lamp covers of 1.5 to 2 mm commonly run 2 to 3 µm beads and reach high haze with less powder.
Silicone or acrylic microspheres
Both chemistries sell in volume, and the choice usually follows processing temperature and price. Widely referenced benchmark grades on the market include Shin-Etsu KMP 590 and KMP 600, DOWSIL 30-424 and PARALOID EXL-5136.
| Property | Silicone (PMSQ) beads | Acrylic (PMMA) beads |
|---|---|---|
| Typical particle size | 1–5 µm | 3–30 µm |
| Refractive index | 1.42–1.45 | about 1.49 |
| Heat resistance | up to about 400 °C | decomposes 280–330 °C |
| Typical use | PC parts, hot processing | PS and PMMA parts, cost-sensitive work |
Acrylic beads cost less and wet out easily, but their 280–330 °C decomposition range sits uncomfortably close to PC melt temperatures of roughly 280 to 300 °C. Silicone powder clears the PC barrel with margin and yellows little over long LED service life.
From our catalog: Ningbo Ultra Color Co., Ltd supplies dyes, organic and inorganic pigments, effect pigments and performance additives, including the light diffusion agent range for plastics, inks and paints. Batches are checked against REACH and RoHS requirements, and retention samples are kept for five years.
Resin choice: PC, PMMA and PS
The matrix changes the arithmetic, because scattering strength follows the index gap. PC and PS, both near 1.59, sit 0.14 to 0.17 above silicone beads, a wide gap that scatters hard, so PC shades reach high haze at 0.3 to 0.5 wt%. PMMA at 1.49 is barely 0.06 above the beads. Weaker contrast scatters less: silicone suppliers note PMMA parts commonly need two to three times the dose to match PC haze. Acrylic beads in PMMA scatter almost nothing, since bead and matrix share an index of 1.49, useful when only a hint of diffusion is wanted.
Processing often seals the decision. PC injects around 280 to 300 °C, hot enough to rule out borderline organic agents, while PS and PMMA run far cooler and accept either chemistry. PS plate is the volume workhorse for television light guides; PC dominates tube covers and streetlight lenses, where heat and impact both matter. When the part carries color as well, the same dispersion logic behind coloring engineering plastics applies to the diffusion beads.
What do formulators ask about light diffusion agents?
How much light diffusion agent does PC need?
Most PC bulb and lamp cover formulations start at 0.3 to 0.5 wt% silicone microspheres and adjust from there. Loadings beyond about 2 wt% are uncommon, since transmittance falls faster than haze climbs. Light guide plates take far less than a shade does.
Does a diffusion agent reduce brightness?
Some loss is unavoidable. Haze and total transmittance trade against each other, and every scattering event leaks a little light. Organic silicone beads keep that loss small, and good PC compounds clear that floor with room to spare.
Silicone or acrylic beads for LED covers?
PC parts usually get silicone, which holds to around 400 °C and yellows little. Acrylic beads suit PS and cooler-running parts at a lower price. If the part must also look whiter, optical brighteners in plastics such as OB-1 or KSN do that job and can sit in the same formula.


